|
|
زمین شناسی مهندسی، جلد ۱۲، شماره ۴، صفحات ۵۹۹-۶۱۶
|
|
|
| عنوان فارسی |
پیشنهاد پوشش بتنی مسلح بر اساس کنترل نشت آب از تونلهای تحت فشار با بهرهگیری از مدل المان محدود |
|
| چکیده فارسی مقاله |
تونلهای تحت فشار با پوشش بتنی، منابعی از جریان نشت آب به تودهسنگ دربرگیرنده خود هستند، از اینرو، طی فرآیند آبگیری مقاومت کمی در برابر فشار نشت آب خواهند داشت و با افزایش فشار آب داخلی تونل، فشار نشت آب به تودهسنگ منتقل خواهد شد. در این شرایط بهواسطۀ درزه، ترک، منافذ و همۀ المانهای تودهسنگ از تمام جهات تحت تأثیر فشار نشت آب قرار میگیرند. این اندرکنش هیدرومکانیکی باعث تغییرات نفوذپذیری المانهای تودهسنگ طی فرآیند آبگیری میشود. بنابراین، تغییرات صورت گرفته در تنش منجر به تغییراتی در ضریب نفوذپذیری و توزیع مجدد میدان نشت میشود. از این رو، در این تحقیق از روش المان محدود بهکمک نرمافزارABAQUS برای مدلسازی این اندرکنش استفاده شده است. در این راستا از دادههای تونل تحت فشار طرح سد و نیروگاه گتوند بهعنوان مطالعۀ موردی بهره گرفته شده است. بهمنظور نزدیککردن مدل به شرایط واقعی، تأثیر تغییرات نفوذپذیری پوشش بتنی و تودهسنگ بر تغییرشکلها و تنشهای ایجاد شده در محیط با استفاده از کد USDFLD به مدل اعمال شده است. نتایج مدل عددی نشان میدهد که بهمنظور کنترل نشت از تونلهای تحت فشار با پوشش بتنی، ضخامت پوشش و آرایش مناسب میلگردها در پوشش بتنی در ممانعت از نشت بیش از حد مجاز از تونل نقش بهسزایی را ایفا میکنند. |
|
| کلیدواژههای فارسی مقاله |
تونل تحت فشار، پوشش بتنی مسلح، اندرکنش هیدرومکانیکی، نرم افزار ABAQUS، نشت، سد و نیروگاه گتوند، کد USDFLD. |
|
| عنوان انگلیسی |
Reinforced Concrete Lining Suggestion based on Seepage Control of Pressure Tunnels using the Finite Element Model |
|
| چکیده انگلیسی مقاله |
Introduction
Pressure tunnels in hydroelectric plants are used to convey water to powerhouses. These tunnels are the sources of seepage flow to the rock formation, thus, during the water filling, they will have a low resistance to seepage and, by increasing the internal water pressure of the tunnel, the inflow force will be transferred to the rock mass. In these conditions, the cracks, pores and all other elements of the rock mass are affected by the seepage forces in all directions. This hydro-mechanical interaction affects changing the stresses and displacements of the rock mass around the tunnel and causes modifications in the permeability of rock elements during the water filling. Therefore, changes in stress distribution lead to alterations in the permeability coefficient and redistribution of the seepage field. In these conditions, since the analytical solution of the problem is not possible, the numerical analysis based on the finite element method has been used in this study.
Material and methods
In this approach, the rock mass is considered as an equivalent continuum in which the effects of discontinuities are taken into account in its material behavior. High-pressure tunnels under internal water pressure requires reinforced concrete lining to prevent hydro-fracturing. The ABAQUS software is capable of analyzing such as seepage from the tunnel, modeling of the steel bars in concrete, and taking into account hydro-mechanical interaction. Thus, the software is used for numerical analysis.
The pressure tunnel of the Gotvand dam and hydroelectric power plant (HPP) scheme is taken as a case study for the numerical simulation. Pressure tunnel of the Gotvand dam located in the southwest of Iran is taken as a case study for the numerical simulation. Among behavioral models in the software, Mohr-Coulomb failure criterion is considered to describe the rock mass, but the principle of effective stress determines the rock mass behavior. Since the concrete lining of the pressure tunnel will undergo two mechanisms of the cracking due to tension and the crushing due to compression, concrete damaged plasticity model is used to predict the response of the concrete elements. The evolution of the yield surface of the concrete lining is also controlled with tensile and compressive equivalent plastic strains, correspondingly.
In this study, the hydro-mechanical interaction is implemented based on the analysis of the pore fluid/deformation analysis, and the direct-coupled method is used to solve the governing equations of the problem. To verify the proposed model, the elastic behavior of the media is simulated to compare the numerical and the analytical solutions and good agreement is obtained. The numerical analyses are carried out the hydro-mechanical interaction with constant permeability coefficient. When cracks develop in the concrete lining at high water pressure, the properties of the concrete lining change and as a result, the stress dependent permeability of the lining and surrounding rock mass in pressure tunnels should be considered. The coefficient of permeability controls the rate of seepage flow in porous and fractured media. Although permeability represents an original property of the porous media, it can be modified when subjected to the stress variations. Instead of changing aperture, the change in the void space or volume is the typical consequence that results to change the permeability coefficient. In order to bring the model closer to the real conditions and in the validation of the new model, the influence of the permeability coefficient variations of the concrete and rock mass on the deformations and stresses of the model has been added to nonlinear analysis by USDFLD code. Increasing the water head in the tunnel during water filling is also considered with the combination of DLOAD and DISP codes in the model.
Results and discussion
Since the lining and rock mass have nonlinear properties and complex behavior, for verification of the model in ABAQUS software, the model is simulated with homogeneous, isotropic and elastic behavior. The results of seepage flow on the interface of the concrete lining and rock mass obtained by analytical and numerical solutions indicate that there is a ±5 % difference between them. Then, the results of the elastic behavior of the model show a good agreement with the results of analytical solutions. Therefore, this numerical model has been employed for the nonlinear analyses.
Finally, the optimal thickness of the concrete lining with the appropriate arrangement of the reinforcement in the reinforced concrete linings is utilized to minimize water losses from the tunnel based on the new model. Thus, the results of the analysis with the aim of reducing the water losses from the tunnel indicate that the suitable arrangement of the steel bars in the concrete lining leads to the distribution of micro cracks in the lining, and the reinforcement stress stays at a lower value with high internal water pressure. Based on the new numerical model, it is suggested that the lining should be designed with the thickness of 40 cm and the reinforcement with the diameter of 16 mm and the spacing of 20 cm.
Conclusion
The results of the numerical model indicate that to control the seepage outflow from concrete-lined pressure tunnels, the thickness of the lining and the suitable arrangement of the steel bars in the concrete lining play a significant role in preventing excessive seepage from the tunnel./files/site1/files/124/3dadashi%DA%86%DA%A9%DB%8C%D8%AF%D9%87.pdf |
|
| کلیدواژههای انگلیسی مقاله |
Pressure Tunnel, Reinforced Concrete Lining, Hydro-Mechanical Interaction, ABAQUS software, Seepage Control. |
|
| نویسندگان مقاله |
احسان داداشی | Ehsan Dadashi
دانشگاه آزاد اسلامی، واحد علوم تحقیقات تهرانhttps://jeg.khu.ac.ir/admin_pg_old2.php?sid=1&slc_lang=fa
علی نورزاد | Ali Noorzad
دانشگاه شهید بهشتی، دانشکدۀ مهندسی عمران، آب و محیطزیست
کورش شهریار | Koroush Shahriar
دانشگاه صنعتی امیرکبیر، دانشکده مهندسی معدن و متالورژی
کامران گشتاسبی | Kamran Goshtasbi
دانشگاه تربیت مدرس، گروه مهندسی معدن مکانیک سنگ
|
|
| نشانی اینترنتی |
http://jeg.khu.ac.ir/browse.php?a_code=A-10-1572-1&slc_lang=fa&sid=1 |
| فایل مقاله |
فایلی برای مقاله ذخیره نشده است |
| کد مقاله (doi) |
|
| زبان مقاله منتشر شده |
fa |
| موضوعات مقاله منتشر شده |
ژئوتکنیک (مکانیک خاک و سنگ) |
| نوع مقاله منتشر شده |
مقاله استخراج شده از پایان نامه |
|
|
|
برگشت به:
صفحه اول پایگاه |
نسخه مرتبط |
نشریه مرتبط |
فهرست نشریات
|
